Wireless -- Advanced

This page allows you to configure advanced features of the wireless LAN interface. You can select a particular channel on which to operate, force the transmission rate to a particular speed, set the fragmentation threshold, set the RTS threshold, set the wakeup interval for clients in power-save mode, set the beacon interval for the access point, set XPress mode and set whether short or long preambles are used.
Click "Apply/Save" to configure the advanced wireless options.

802.11n Band:	2.4GHz
Channel:	Auto 1 2 3 4 5 6 7	Current: 1 (interference: acceptable)
Auto Channel Timer(min)

MIMO-OFDM:

Auto Disabled

Bandwidth:	20MHz 40MHz	Current: 20MHz
Control Sideband:	Lower Upper	Current: N/A
MIMO Data Rate:	Auto Use 54g Rate 0: 6.5 Mbps or 13.5 Mbps 1: 13 Mbps or 27 Mbps 2: 19.5 Mbps or 40.5 Mbps 3: 26 Mbps or 54 Mbps 4: 39 Mbps or 81 Mbps 5: 52 Mbps or 108 Mbps 6: 58.5 Mbps or 121.5 Mbps 7: 65 Mbps or 135 Mbps 8: 13 Mbps or 27 Mbps 9: 26 Mbps or 54 Mbps 10: 39 Mbps or 81 Mbps 11: 52 Mbps or 108 Mbps 12: 78 Mbps or 162 Mbps 13: 104 Mbps or 216 Mbps 14: 117 Mbps or 243 Mbps 15: 130 Mbps or 270 Mbps
RTS/CTS Protection:	Off Auto
Support MIMO Clients Only:	Off On
RIFS Advertisement:	Off Auto
OBSS Coexistence:	Disable Enable
RX Chain Power Save:	Disable Enable	Power Save status:	Full Power
RX Chain Power Save Quiet Time:
RX Chain Power Save PPS:

54g™ Rate:	1 Mbps 2 Mbps 5.5 Mbps 6 Mbps 9 Mbps 11 Mbps 12 Mbps 18 Mbps 24 Mbps 36 Mbps 48 Mbps 54 Mbps
Multicast Rate:	Auto 1 Mbps 2 Mbps 5.5 Mbps 6 Mbps 9 Mbps 11 Mbps 12 Mbps 18 Mbps 24 Mbps 36 Mbps 48 Mbps 54 Mbps
Basic Rate:	Default All 1 & 2 Mbps 1 & 2 & 5.5 & 6 & 11 & 12 & 24 Mbps
Fragmentation Threshold:
RTS Threshold:
DTIM Interval:
Beacon Interval:
Global Max Clients:
XPress™ Technology:	Disabled Enabled

54g™ Mode:	54g Auto 54g Performance 54g LRS 802.11b Only
54g™ Protection:	Off Auto

Regulatory Mode:	Disabled 802.11h 802.11d
Pre-Network Radar Check:
In-Network Radar Check:
TPC Mitigation(db):	0(off) 2 3 4

Afterburner Technology:

Disabled Enabled

(Disable WMM for Selection)

Preamble Type:

long short

Transmit Power:

20% 40% 60% 80% 100%

WMM(Wi-Fi Multimedia):

Auto Disabled Enabled

WMM No Acknowledgement:

Disabled Enabled

WMM APSD:

Disabled Enabled

Iperf Support:	Disable Enable
Video Error Correction:	RX Auto Enable Decode RX Disable Decode TX Enable Sequencer TX Enable Sequencer (IPTV Mode) TX Enable Encode TX Enable Encode (IPTV Mode)

Wireless Mode:	Access Point Wireless Ethernet
URE:	OFF ON
URE Mode:	Bridge (Range Extender) Routed (Travel Router)
STA Retry Time(sec):

Beamforming Transmission (BFR):	Disabled Enabled
Beamforming Reception (BFE):	Disabled Enabled

Band Steering:	Disabled Enabled
BSD Role Config:	IP Addr	Port Number
Helper Addr & Port:
Primary Addr & Port

Enable Traffic Scheduler:	Disable Enable
Airtime Fairness:	Disable Enable

Stalled Link Detection Treshold:
Packet Saving Retry Limit:

ACS Mode:	SCS FCS
DFS Channel Selection:	Disable Enable Reentry
CI Scan Interval:
CI Scan Timeout:
Scan Result Expiry:
Tx IDLE Frame Rate:
Chan Dwell Time:
Chan FLOP Period:
Sample Period:
Sample Count:
Non-TCP Stream TxFail Threshold:
TCP Stream TxFail Threshold:
DFS Reentry Window Settings:	Seconds	Threshold
Immediate Reentry:
Deferred Reentry:
Channel Active: